Table of Content
Shared Line next to the directory number means that the directory number appears on more than one device in the same partition. Refer to "Directory Numbers" in the Cisco CallManager System Guide for more information. Step 4From the Directory Numbers list, choose the line that you want to remove. Step 3Choose the device name that contains the directory number that you want to remove. Step 4From the Directory Numbers list, click the line that you want to update.
NoteDo not configure this field if you are using extension mobility because it does not support device owners. •Choose the name of the phone that you want to delete from the list to display its current settings and click Delete. •Check the check boxes next to the phones that you want to delete and click Delete Selected. •Close—Returns you to the previous window without restarting or resetting the chosen devices. Step 2To locate a specific phone, enter search criteria and click Find.
Displaying the MAC Address of a Phone
For Cisco VG248 gateways, begin the description with VGC. •Restart—Restarts the chosen devices without shutting them down . NoteFor information on obtaining the MAC address, see the "Displaying the MAC Address of a Phone" section. NoteAdd the Cisco VG248 Phone Ports from the Gateway Configuration window of Cisco CallManager Administration.
If you want to choose a different service, click Back and repeat Step 5. Check the Media Termination Point Required check box if you want to use a media termination point to implement features. Uncheck the Media Termination Point Required check box if you do not want to use a media termination point to implement features. This check box specifies that Cisco CallManager waits to receive the far-end H.245 Terminal Capability Set before it sends its H.245 Terminal Capability Set. To specify that Cisco CallManager should initiate capabilities exchange, uncheck this box.
Removing a Directory Number From a Phone
The Phone Configuration window displays with the directory number removed. The change gets automatically applied to the phone; however, you can click Reset Phone. For more information, see the "Resetting a Phone" section. A list of phones that match the search criteria displays.
Use the number that receives calls when call forward is enabled on the phone. Use the Self Care portal to set up more complicated call forward functions, for example, when your line is busy. You wants a different phone model from their current model. Contact your administrator if you don't know your code or if you need a new one. You can change the angle of the phone, except the Cisco IP Phone 7811, to eliminate glare on the screen. In certain circumstances, users who dialed a number that was busy received the reorder tone.
Cisco One-Year
The documentation set for this product strives to use bias-free language. Learn more about how Cisco is using Inclusive Language. Your other option is to install a firewall / router on your home office LAN that can create a LAN to LAN VPN tunnel back to the head office. Without this VPN tunnel, the 7942 can't communicate with CUCM, and hence will never work.
If check box is not checked, Cisco CallManager ignores the DN. This check box enables delivery of the display information element in SETUP and CONNECT messages for the calling and called party name delivery service. Check this check box if this phone supports extension mobility. The phone button template determines the configuration of buttons on a phone and identifies which feature is used for each button. To specify the audio source that is played when the network initiates a hold action, click the drop-down arrow and choose an audio source from the list that displays. To specify the audio source that plays when a user initiates a hold action, click the drop-down arrow and choose an audio source from the list that displays.
Configuring Cisco IP Phones
Clients VPN into Dallas, then there is a data connection into denver. Well, it turns out the connection between Dallas and Denver, is not MPLS, just a straight connection. I find that the IP Communicator to work a little better and easier to administrator, rather than send 79xx phones home with people. With IPC, you can simply load it on the laptop or home PC, configure VPN software, and connect. With the 79xx, you will need to have a hardware VPN solution, unless you enable SIP on the 79xx series and create a SIP connection back to CCM.
By default, this URL accesses a Cisco IP Phone User Options window that was configured during installation. The softkey template determines the configuration of the softkeys on Cisco IP Phones. Leave this field blank if the device pool contains the assigned softkey template. Choose the appropriate location for this Cisco IP Phone. The location specifies the total bandwidth that is available for calls to and from this location.
Pick your business phone plan.Choose the plan that fits your business with powerful features. A softphone is a piece of software or a mobile app that lets you receive and make phone calls. With a VoIP service, you can dial numbers on any telephone or mobile network. If you want your phone calls to sound great, you should invest in a high-end VoIP desk phonelike the Polycom VVX601.
Click the desired partition name in the list of partitions that displays in the Select item to use box, and click OK. TipIf you need more than two lines, you can increase the lines by modifying the phone button template for the phone type . Some phone types, however, only support one or two lines .
The specific steps depend on hardware and the number of employees. With the Nextiva App for desktop, all you need to handle calls efficiently is a quality USB or Bluetooth headset. If you’re on your laptop, you already have a microphone and speakers ready for instant phone calls. The Nextiva App is also available for any Android or iOS device so your team can handle business calls on their cell phones. And your network hardware can also become a bottleneck. If the router or network can’t handle peak traffic, you could experience choppy audio or other issues like dropped calls.
Destination—This setting indicates the directory number to which all calls are forwarded. NoteDo not configure Auto Answer for devices that have shared lines. NoteMake sure that the headset or speakerphone is not disabled when you choose Auto Answer with headset or Auto Answer with speakerphone. Values can include numeric characters and route pattern wildcards and special characters except for (.) and (@). Perform the following procedure to remove a directory number from a specific phone.
No comments:
Post a Comment